Resin Print Stuck to Build Plate: How To Remove?

Resin printing is a great way to produce high quality prints, but the resin can be difficult to remove from the build plate. In this blog post, we will show you how to remove the resin print stuck to build plates quickly and easily. We will also show you how to prevent the resin from sticking to the build plate in the first place. Enjoy!

The best way to remove a resin print stuck to the build plate is to use a metal scraper. Gently insert the scraper under the edge of the print and then push it forward. The scraper should gradually weaken the adhesion and allow the print to be removed from the build plate. Be careful not to damage the print as you remove it. If that doesn’t work, try using flush cutters or a razor blade scraper. You can also try using a heat gun or air dryer to soften the resin. Keep in mind that over-curing the resin can make it warp and crumbly, making it even harder to remove. Be careful not to damage the print as you remove it. With a little practice, you’ll be able to remove prints quickly and easily without any damage.

How to remove resin prints from build plate?

First, make sure that the build plate is properly heated. If it’s too cold, the resin will be more likely to stick; if it’s too hot, the resin will be more likely to warp. You should also clean the build plate regularly with isopropyl alcohol to remove any buildup that could be preventing the prints from releasing.

Finally, if all else fails, you can always try using a metal scraper to gently pry the print off the build plate. Start at the edge of the print and work your way underneath; with a little patience, you should be able to release even the stubborn prints.

Using a Metal Scraper to Remove the Resin print:

When it comes time to remove your resin print from the build plate, there are a few things to keep in mind.

  • First, always use a metal scraper – never use anything else, as you risk damaging your print or the build plate itself.
  • Second, start by gently scraping away any excess resin from the edges of the print.

Once you’ve done that, you can begin to apply more pressure in order to remove the print. Be careful not to apply too much pressure, as you don’t want to break the print. If it’s proving difficult to remove, you can try heating up the build plate with a heat gun or hair dryer – this will help to loosen the resin and make removal easier.

Watch below video for a detailed demonstration:

How to Remove Cured Resin From Build Plate

If you’re trying to remove a cured print or a piece of cured resin, there are a few different methods you can try.

  • Scrape it off with a scraper or razor blade.
  • Use a heat gun on the resin.
  • Over-cure the resin with a UV light or in the sun, which will make it warp and easier to remove.
  • Soak the build plate in IPA or acetone for a few hours.
  • Place the build plate in a non-food safe freezer or use compressed air to blow the resin off.

a. Scrape it off with a scraper or razor blade

One of the best tools for removing resin is a metal scraping tool. These tools are designed to safely scrape away resin without damaging the underlying surface.

If you’re working with cured resin, you may need to use a little elbow grease to get it started. But once you start scraping, the process should go relatively quickly.

When using a metal scraping tool, be sure to work slowly and carefully. This will help prevent damage to the surface and will also make it easier to control the scraping tool. In addition, be sure to scrape in a well-ventilated area so that you don’t inhale any fumes from the heated resin.

a.1) Warner 4″ Pro Grip Stiff Broad Knife to remove resin prints

The Warner 4″ Pro Grip Stiff Broad Knife is the perfect tool for removing resin prints. The sharp, serrated blade easily cuts through the toughest resin, and the robust handle provides a comfortable grip for even the most challenging jobs.

The knife also features a convenient finger guard to prevent accidental cuts. Whether you’re a professional printer or a hobbyist, the Warner 4″ Pro Grip Stiff Broad Knife is the ideal tool for safely and effectively removing resin prints.

a.2) Razor blade scraper

Razor blade scraper is a manual tool that consists of a handle and a small, sharp blade. It is primarily used for removing resin from the build platform or print bed. The advantage of using a razor blade scraper is that it is very precise and allows you to remove only the desired amount of resin. In addition, it is relatively inexpensive and easy to find.

The main disadvantage of using a razor blade scraper is that it can be dangerous if not used properly. The blade is very sharp and can easily cut through skin. In addition, the blade can break if it hits a hard surface such as the build platform.

Therefore, it is important to be careful when using this tool and to always keep the Blade pointed away from your body.

a.3) Titan Tools – 2-Pc Multi-Purpose Razor Scraper Set

The Titan Tools – 2-Pc Multi-Purpose Razor Scraper Set is designed to make removing resin prints quick and easy. The set includes two scrapers: a straight scraper for large surfaces and a curved scraper for smaller, hard-to-reach areas.

The scrapers are made of stainless steel with a comfortable grip, and the blades are sharp enough to easily remove even the most stubborn prints.

In addition, the set includes a razor blade adapter that allows you to use standard razor blades with the scrapers. With the Titan Tools – 2-Pc Multi-Purpose Razor Scraper Set, you can quickly and easily remove resin prints from your build plate.

b) Use a heat gun on the resin

In order to remove the resin from your build plate, you will need to use a heat gun. First, make sure that the build plate is level and secure. Then, position the heat gun about six inches away from the resin.

Slowly move the heat gun back and forth over the resin until it becomes soft and pliable.

At this point, you can use a spatula or putty knife to remove the resin from the build plate. Be careful not to scratch the surface of the build plate while you are removing the resin.

Once the resin is removed, you can allow the build plate to cool before starting your next print job.

b.1) Asnish 1800W Heavy Duty Hot Air Gun

The Asnish 1800W Heavy Duty Hot Air Gun is a powerful tool that can remove resin quickly and easily. The gun uses hot air to soften the resin, making it easy to remove from the surface of the print.

There are three different heat settings, so you can choose the one that is best for your particular job. The gun also comes with a stand, so you can keep it steady while you work.

The Asnish 1800W Heavy Duty Hot Air Gun is an essential tool for anyone who works with resin prints. It makes removing resin quick and easy, and it helps to prevent damage to the surface of the print.

c) Soak the Build Plate in IPA or Acetone

When you remove a resin print from the build plate, there is usually some residue left behind. This can make it difficult to get a clean print on the next layer, and can eventually lead to build-up that can damage the build plate.

Soaking the build plate in IPA or acetone can help to remove this residue and keep the build plate clean.

IPA is a strong solvent that will quickly break down resin, making it easy to wipe away. Acetone is also a strong solvent, but it evaporates quickly, so it’s important to make sure that all of the acetone has evaporated before starting the next print.

Either of these solvents can be used to help keep the build plate clean and ensure that your prints come out looking their best.

c.1) Solimo 91% Isopropyl Alcohol to remove resin prints

Solimo 91% Isopropyl Alcohol is an effective way to remove resin prints. The alcohol dissolves the resin, making it easy to remove the print from the build plate. In addition, the Solimo 91% Isopropyl Alcohol is less likely to damage the build plate than other solvents. As a result, it is a good choice for removing resin prints.

d) Place the build plate in a non-food safe freezer or use compressed air to blow the resin off.

One way to help remove resin prints is to place the build plate in a non-food safe freezer for a few minutes. This will cause the resin to contract and release its grip on the build plate. As a result, you will be able to remove the print with minimal damage.

Be sure to use gloves when handling the build plate, as the cold temperature can cause skin irritation. Just be sure to allow the build plate to return to room temperature before attempting another print.

d.1) Using Compressed Air:

Using compressed air to blow the resin off from the build plate is a simple and effective way to clean your 3D printer. First, remove the build plate from the 3D printer. Next, point the nozzle of the compressed air can at the build plate and hold it about 6 inches away.

Spray the build plate in short bursts until all of the resin has been removed. Finally, wipe down the build plate with a clean cloth to remove any residue.

d.2) Falcon Dust-Off Compressed Gas Duster

When it comes to removing resin prints, the Falcon Dust-Off Compressed Gas Duster is one of the best products on the market. Not only does it quickly and easily remove resin prints, but it also leaves behind a clean surface that is ready for new prints.

The duster works by using compressed gas to blast away the resin, and the disposable canister ensures that there is no mess left behind.

In addition, the duster is safe to use on a variety of surfaces, making it a versatile tool for any 3D printer owner. Whether you’re trying to remove an old print or prepare a new build surface, the Falcon Dust-Off Compressed Gas Duster is an essential tool for anyone who owns a 3D printer.

Conclusion:

In conclusion, there are a few ways to remove resin prints stuck to build plate. The most effective way will depend on the type of resin and printer being used. Hopefully, this article has helped provide some insight into the process for removing resin prints from a build plate. Have you had success with another method not mentioned here? Let us know in the comments below!

We will be happy to hear your thoughts

Leave a reply

Enable registration in settings - general